32-inch gravel wheels: questions and answers
- Are 32-inch wheels faster than 29-inch (700c) wheels on gravel?
- How sure is that result?
- What is a 32-inch wheel?
- Why would a bigger wheel roll faster?
- What are the downsides of 32-inch wheels?
- Are 32-inch wheels slower on climbs?
- Do 32-inch wheels make a difference on pavement?
- What tyre pressure should a 32-inch wheel run?
- How does the simulator work?
- How accurate is it? Has it been validated?
- What can I change in the simulator?
- Is Wheel Size Lab free? What do I need to run it?
- Which wheel sizes have real test data behind them?
Are 32-inch wheels faster than 29-inch (700c) wheels on gravel?
Probably yes, but by less than the headlines suggest. In the simulator's default test, with the same rider, the same 220 watts and the same 50 mm tyres at matched pressure, the 32″ bike finishes a mixed 5 km course 6.5 seconds ahead after about 12 minutes. That is 0.9%, like finding about 3 extra watts. Most of the gain comes from rough and loose ground; on smooth pavement the difference is close to zero.
How sure is that result?
Not very. It depends on whose data you trust. Calibrated to the sceptical view that diameter does not change tyre losses, the 32″ bike loses the same race by 2.1 seconds. Calibrated to the maker's data it wins by 14.7 seconds. Every published test so far is small and none is peer reviewed, so the simulator shows the whole range instead of a single number.
What is a 32-inch wheel?
A 32″ wheel has a 686 mm bead seat diameter, against 622 mm for 700c, which is the same rim size as a 29er. With a 50 mm tyre the outer diameter is about 786 mm instead of 722 mm, roughly 9% bigger.
Why would a bigger wheel roll faster?
Three things change. The contact patch gets longer and flatter (about 140 mm against 134 mm in the default test), so the tyre casing bends less. The longer patch spreads the load, so the tyre sinks less into loose gravel. And the wheel meets each bump at a shallower angle (15.9° against 16.6° on a 15 mm bump), so every hit slows the bike less and shakes the rider less.
What are the downsides of 32-inch wheels?
In the simulated bikes the 32″ version is 428 g heavier, its wheels have 34% more rotational inertia, and its drag area is about 1% higher because the wheels show more frontal area. Real 32″ frames also have a longer wheelbase and more trail, and tyre and rim choice is still limited. Fit for shorter riders and handling are not modelled by the simulator.
Are 32-inch wheels slower on climbs?
Not in this test. On the 4% and 6% gravel climbs the extra 428 g costs about 0.8 W, but the rolling savings on rough gravel are bigger, so the 32″ bike still gains 1.2 and 1.4 seconds on those two segments. On a smooth, steep climb the weight penalty would win.
Do 32-inch wheels make a difference on pavement?
Hardly. With no bumps and nothing to sink into, the only help is a little less tyre flex. In the default race the 32″ bike gains 0.1 seconds over 500 m of smooth pavement.
What tyre pressure should a 32-inch wheel run?
Slightly lower than a 700c wheel for the same tyre drop. In the default setup (86 kg system weight, 50 mm tyres) the simulator suggests 25.0 psi for 700c and 23.9 psi for 32″. You can also set pressures by hand or run a pressure sweep to find the fastest pressure for a surface.
How does the simulator work?
It solves a power balance many times a second for each bike: the rider's power, after drivetrain losses, has to pay for air drag, tyre flex, loose-surface losses, bumps and vibration, gravity and acceleration, including spinning up the wheels. Both bikes roll over exactly the same generated surface profile, with the tyre contact patch and a spring-and-damper rider simulated on every bump.
How accurate is it? Has it been validated?
The model is anchored to published measurements: drum rolling resistance tests, wind tunnel drag figures, measured wheel weights and inertia, and the field tests of 29″ against 32″ wheels. The Research page shows every published test next to what the model predicts for the same conditions. The big uncertainty is how strongly rolling losses depend on wheel diameter, which is why you can switch between five calibrations.
What can I change in the simulator?
Almost everything: wheel size (650b, 700c, 32″, 36″ or any rim diameter), tyre width, tyre model and pressure, bike and wheel weights, rider weight, height, power and riding position, wind speed and direction, temperature and altitude, and the course itself, segment by segment, with seven surfaces from pavement to rooty singletrack.
Is Wheel Size Lab free? What do I need to run it?
It is free and runs in your browser on a computer or a phone. There is nothing to install and no account. It needs WebGL, which every current browser has. Your settings are saved only in your own browser.
Which wheel sizes have real test data behind them?
Only 700c and 32″. The 650b and 36″ presets, and any custom rim size, are extrapolations of the same physics and are marked as untested in the simulator.